{"product_id":"hammer-front-bumper-w-stinger-and-fog-lights-for-jeep-jk-jku","title":"Motobilt Jeep Wrangler JK \/ JKU Hammer Front Bumper w\/stinger and fog lights","description":"\u003c!--[difficulty:2]--\u003e\r\n\u003cp\u003eThe Motobilt Jeep JK Front the Hammer Bumper is a 48.5-inch wide, sleek, tight-fitting design proudly made in the USA. Our JK The Hammer Bumper is 3D CAD designed to ensure the best possible fit to your Jeep JK. The bumper will fit all year models of the Jeep JK 2 door and 4 door JK Unlimited. The front d-ring mounts are CNC cut from 3\/4-inch-thick steel plate and pass through the bumper where they weld to the bumper mounting plates in addition to the bumper body. This was done for added strength to the recovery point.\u003c\/p\u003e\r\n\u003cp\u003eThe Hammer bumper has provisions to mount the factory fog lights or aftermarket LED fog lights. We have pre-installed riv nuts for 10-24 screws in the factory bolt pattern. The Hammer bumper can be run with or without the optional skid plate. To install the skid plate, you have to trim approx. 1 inch off each side of the crash bars. If you remove the skid plate later, the part that you trimmed will not be seen. The ends of the Hammer bumper taper up for tire clearance. Each cut in the bumper was intentional to keep it tight to the frame rail for a better approach angle. The main construction of the bumper is fabricated from 3\/16-inch-thick high strength steel plate. The bumper also serves as a winch mount. The top side of the JK The Hammer Bumper has bolt holes for a recovery winch.\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003ch4\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/h4\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eJeep JK The Hammer 48.5-inch front bumper with stinger\u003c\/li\u003e\r\n\u003cli\u003eFits all year models of the Jeep JK 2 door and 4 door JK Unlimited\u003c\/li\u003e\r\n\u003cli\u003e\r\n\u003cstrong\u003eWinch:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eOur winch bumper is designed to fit a standard mounting pattern of 10\" x 4.5\" and has been tested with the Warn VR EVO and Zeon series winches. It may also fit other untested winches.\u003c\/span\u003e\r\n\u003c\/li\u003e\r\n\u003cli\u003eFabricated from 3\/16-inch-thick high strength steel plate.\u003c\/li\u003e\r\n\u003cli\u003e\r\n\u003cstrong\u003eBolt on\u003c\/strong\u003e design.\u003c\/li\u003e\r\n\u003cli\u003e\r\n\u003cstrong\u003eSway Bar Compatibility: \u003c\/strong\u003eWorks with all factory sway bars including Rubicon and works with Anti-Rock as well.\u003c\/li\u003e\r\n\u003cli\u003e3\/4-inch-thick steel d-ring mounts\u003c\/li\u003e\r\n\u003cli\u003ePass through d-ring mounts weld to the bumper.\u003c\/li\u003e\r\n\u003cli\u003e\r\n\u003cstrong\u003eFog Light\u003c\/strong\u003e holes for factory fog lights.\u003cbr\u003e\r\n\u003c\/li\u003e\r\n\u003cli\u003ePre-installed riv nuts for 10-24 screws in the factory bolt pattern.\u003c\/li\u003e\r\n\u003cli\u003e\r\n\u003cstrong\u003eProudly Made in the USA:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan\u003eCrafted with precision and pride in the United States, ensuring the highest quality and supporting American manufacturing.\u003c\/span\u003e\r\n\u003c\/li\u003e\r\n\u003cli\u003eSold as each.\u003c\/li\u003e\r\n\u003cli\u003eWeight: 80lbs (approx.)\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch4\u003eFits:\u003c\/h4\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eJeep Wrangler JK \/ JKU 2007-2018\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eIf installing a winch, MB1002 or MB1141 fairlead mount will also need to purchase.\u003c\/li\u003e\r\n\u003cli\u003eShips raw steel. Must be painted or powder coated to prevent rust.  See (\u003ca rel=\"noopener\" href=\"https:\/\/motobilt.com\/blogs\/first-blog\/steel-it?_pos=3\u0026amp;_sid=2ef388d16\u0026amp;_ss=r\" target=\"_blank\"\u003eSteel-It\u003c\/a\u003e)\u003c\/li\u003e\r\n\u003cli\u003eNo cutting required on the frame rails on your Jeep JK\u003c\/li\u003e\r\n\u003cli\u003eThe two outside top bolt holes on your frame need to be drilled out to 9\/16 inch.\u003c\/li\u003e\r\n\u003cli\u003e2012 and newer models will need a vacuum relocation pump bracket PN MB2060\u003c\/li\u003e\r\n\u003cli\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/motobilt.com\/products\/jeep-jk-front-bumper-skid-plate-07-18-wrangler-jk-the-hammer\" style=\"color: #ff2a00;\" target=\"_blank\"\u003eSkid plate sold separately.\u003c\/a\u003e\u003c\/span\u003e\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/2714\/8736\/files\/mb1025_-_shipping.pdf?v=1660686055\" rel=\"noopener noreferrer\" class=\"btn\" target=\"_blank\"\u003eProduct Components\u003c\/a\u003e\u003c\/p\u003e\r\n\u003ch4\u003eInstructions\u003c\/h4\u003e\r\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/2714\/8736\/files\/MB1025_-_Assembly_Instructions.pdf?v=1698766510\" class=\"btn\"\u003eInstallation Instructions\u003c\/a\u003e\u003c\/p\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":44231237468259,"sku":"MB1025F-S","price":839.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0659\/2548\/0547\/files\/mb1025-s-1_1.jpg?v=1780342961","url":"https:\/\/offroadnchillstore.com\/products\/hammer-front-bumper-w-stinger-and-fog-lights-for-jeep-jk-jku","provider":"Off Road n Chill Store","version":"1.0","type":"link"}